# Folder dieline guide: A4, A5, 9 × 12 and capacity pocket folders

> How a pocket folder dieline is built, what A4, A5, 9 × 12 in and capacity folder sizes really hold, how glue tabs, gussets and card slits change the blank, and what to send your printer.

Canonical: https://dielinemaker.com/blog/folder-dieline-sizes
Last updated: 2026-11-10

A pocket folder looks like the simplest piece of print in a sales kit. Its dieline still has to answer three questions: what goes inside, how thick the stack is, and how the pockets are held on.

**Quick answer:** A pocket folder dieline is one flat blank: back cover, an optional capacity spine and front cover side by side, with a pocket hanging below each cover and a narrow glue tab on each pocket’s outer edge. The pocket folds up onto the cover and the tab is glued behind it. Size the covers from the contents plus clearance (9 × 12 in for US Letter, about 220 × 310 mm for A4), add a spine or pocket gusset for thick stacks, and allow for the glue tab, which takes width away from the pocket opening.

## What is on a pocket folder dieline?

Lay a presentation folder open, printed side down, and you are looking at most of its dieline. The two covers sit side by side and meet at the spine fold. In a standard folder that spine is a single crease; in a capacity folder it is a flat strip between two parallel creases. Below each cover hangs a pocket panel that folds up 180° onto the inside of the cover. On the outer edge of each pocket is a glue tab, which folds behind the pocket first and is glued to the cover, closing that side so papers cannot slide out.

Everything else is an option on that base: a pocket on one side only, angled or curved pocket tops, four short slits that hold a business card, a lock flap that tucks into the front cover, or a hanging tab with a Euro slot for retail pegs. Each of those adds marks to the same blank, so they belong on the dieline from the start rather than as an afterthought in the artwork file.

| Part | Line type | What to check |
| --- | --- | --- |
| Outer edge of covers, pockets and tabs | Cut | Closed path; pocket tops follow the chosen shape |
| Spine (one or two lines) | Crease | Two creases spaced to the spine width for a capacity folder |
| Pocket fold at each cover’s bottom edge | Crease | Pocket depth measured from this fold |
| Glue tab hinge on each pocket | Crease | Tab width and glue area kept free of heavy coating |
| Business card slits | Cut | Slits sized to the card you will actually insert |

## Common folder sizes and what they hold

Folder sizes are named after the paper they carry, not the blank they are cut from. A US 9 × 12 in folder (229 × 305 mm closed) holds 8.5 × 11 in Letter sheets with about half an inch of width and an inch of height to spare. A4 sheets are 210 × 297 mm, so an A4 folder is usually a little wider and taller than the paper; DielineMaker’s A4 preset uses 220 × 310 mm covers. A5 (148 × 210 mm) suits menus, invitations and small certificates, and the A5 preset is a 160 × 225 mm mini folder with a single curved pocket.

The table lists the folder presets in the presentation folder template. Each one is a starting point: change the width, height, pocket depth or spine and the dieline is rebuilt for the new size.

| Preset | Closed cover size | Built for |
| --- | --- | --- |
| 9 × 12 in pocket folder | 229 × 305 mm | US Letter sheets, two pockets, card slits |
| A4 presentation folder | 220 × 310 mm | A4 sheets, two pockets |
| Slim A4 presentation folder | 218 × 305 mm | Light A4 kits with less margin |
| A5 mini folder | 160 × 225 mm | A5 menus, invitations, certificates |
| Half-letter presentation folder | 155 × 230 mm | 5.5 × 8.5 in inserts |
| US legal presentation folder | 235 × 370 mm | 8.5 × 14 in legal sheets |
| A3 presentation folder | 310 × 435 mm | A3 drawings and posters folded once |
| Capacity folder | 229 × 305 mm, 10 mm spine | Thick proposals or brochure sets |

See: [Open the presentation folder template](https://dielinemaker.com/dielines/presentation-folder)

## Why an A4 folder is not exactly A4

The cover size is not the space your paper gets. The glue tab sits between the pocket and the cover along the outer edge, so the clear width inside the pocket is roughly the cover width minus the tab. With a 220 mm cover and a 12 mm glue tab, about 208 mm remains between the glued edge and the spine fold, which is slightly less than an A4 sheet’s 210 mm. Thin sheets often still sit comfortably because the pocket’s inner edge is open, but a thick stack or a stiff brochure will bow or catch on the fold.

For that reason, check the clear width before you lock the artwork. If the contents must lie flat, widen the covers (our A4 worked example uses 230 × 315 mm) or narrow the glue tab within what your finisher accepts. Pocket depth is the other half of fit: around a third of the cover height is common, and 4 in (about 102 mm) is the familiar US default. Deeper pockets hold papers more securely but cover more of the inside artwork.

- Clear width ≈ cover width − glue tab.
- Allow a few millimetres of height above the tallest sheet so it does not touch the top cut.
- Measure the real insert stack, not the paper size printed on the ream.
- Make one full-size sample with the actual sheets before approving a run.

See: [Follow the A4 folder walkthrough](https://dielinemaker.com/learn/presentation-folder)

## Capacity spines and gusset pockets

A standard folder closes on a single crease, so it only stays flat with a few sheets inside. When the kit is thicker, there are two separate allowances, and they solve different problems. A capacity spine is a flat strip between two parallel creases where the covers meet; it lets the closed folder hold depth without springing open. A pocket gusset is a depth strip at the bottom and outer edge of each pocket, again formed by paired creases, so the pocket itself can swell around a stack instead of cutting into it.

Both are sometimes called a “gusset folder”. In practice you choose by where the bulk is. A bound proposal or several brochures together need a spine about as wide as the stack. A pocket that carries loose sheets on one side only may need just a gusset. In the DielineMaker template the spine and the pocket gusset each run from 0 to 25 mm, and the capacity preset starts with a 10 mm spine and angled pockets.

| Allowance | Where it is | Use it when |
| --- | --- | --- |
| Single crease (no spine) | Between the covers | A handful of sheets |
| Capacity spine | Flat strip between two spine creases | The closed folder must hold a thick stack |
| Pocket gusset | Strip at the pocket bottom and outer edge | A pocket must expand around its contents |

See: [Start from the capacity folder preset](https://dielinemaker.com/dielines/presentation-folder--folder-capacity)

## How big is the flat blank?

For a two-pocket folder with no spine, the flat blank is approximately two cover widths plus two glue tabs wide, and one cover height plus the pocket depth tall. The A4 worked example in our learning guide, with 230 × 315 mm covers, 100 mm pockets and 12 mm tabs, measures 484 × 415 mm across the cut lines and 490 × 421 mm with 3 mm bleed. A capacity spine adds its width to the first number; a gusset adds a little to both.

That is why a folder never prints on an A4 or A3 sheet: even an A4 folder blank is larger than A3 (297 × 420 mm). Folders are printed on a larger press sheet and die-cut, then the tabs are folded and glued. Your printer decides the sheet and the imposition, so send them the blank size early, especially for unusual sizes.

1. **Width** — 2 × cover width + spine + 2 × glue tab (two pockets).
2. **Height** — Cover height + pocket depth, plus any hanging tab or top lock flap.
3. **Bleed** — Add bleed all round, commonly 3 mm, for the print file.
4. **Confirm** — Ask the printer for the press sheet and grain direction they will use.

## Placing artwork on a folder dieline

A folder has four printed faces that matter: the front cover, the back cover, and the two insides that are only seen when it opens. The visible face of each pocket is printed on the same side of the sheet as the outside covers, because the pocket flips over as it folds up onto the inside. On the flat sheet that pocket artwork sits below the cover and has to be placed upside down relative to the cover art. Getting it the wrong way round is a classic folder proofing mistake, and it is easy to catch in a 3D fold preview.

Keep text and logos clear of the spine creases, the pocket fold and the card slits. Leave the glue tab area free of heavy coatings or laminate unless your finisher says otherwise, because some coatings stop glue from holding. If the folder has a business card on the right pocket, check the slits against the card you will actually use. The template’s slits are set for an 89 × 51 mm (3.5 × 2 in) card; a European 85 × 55 mm card needs different slit spacing, so confirm it with a sample.

## What to send your printer

Send the dieline as a vector file with cuts and creases on separate, named layers or spot colours, plus the print PDF with bleed. State the closed size, the spine width, pocket depth, board and caliper, and whether card slits, a lock or a hanging tab are included. Many folder printers have their own standard dies, and using a size they already hold can save the cost of a new cutting die, so ask before inventing a new size.

DielineMaker lets you size the folder, add the options above, place front, back and inside artwork and fold it in 3D for free. Production downloads of the dieline as PDF, SVG or DXF are part of Pro.

- Closed size and which paper it must hold.
- Spine width and pocket gusset, if any.
- Pocket depth, shape and which side has pockets.
- Card slits, lock flap or hanging tab.
- Board grade and caliper; coating and glue notes.

See: [Design a folder free](https://dielinemaker.com/dielines/presentation-folder)

## Common questions

### What size should an A4 folder dieline be?

Make the covers larger than the 210 × 297 mm sheet. 220 × 310 mm is a common starting size, but check the clear width once the glue tab is taken off; for thick contents or a strict flat fit, go wider, as in the 230 × 315 mm worked example.

### What is the difference between a pocket folder and a presentation folder?

Usually nothing: both names describe a printed two-panel cover with glued pockets inside. Some printers reserve “presentation folder” for the heavier, laminated version used in sales and press kits.

### How deep should a folder pocket be?

About a third of the cover height is a common default; 4 in (around 102 mm) is the familiar US size on 9 × 12 in folders. Make it deeper to hold papers more securely, shallower to show more inside artwork.

### When do I need a capacity folder?

When the closed folder must hold more than a few sheets without springing open. Make the spine roughly as wide as the stack; add a pocket gusset if a pocket must also expand around its contents.

### Can I make a folder without pockets?

Yes. In the presentation folder template set Pockets to “No pockets” for a plain two-panel cover, or choose corner retainers to hold a single flat card, as on a menu or certificate cover.

Next step: [Open the folder template](https://dielinemaker.com/dielines/presentation-folder)

## Related

- [Presentation folder template](https://dielinemaker.com/dielines/presentation-folder)
- [A4 folder dieline](https://dielinemaker.com/dielines/presentation-folder--folder-a4)
- [A5 folder dieline](https://dielinemaker.com/dielines/presentation-folder--folder-a5)
- [A4 folder walkthrough](https://dielinemaker.com/learn/presentation-folder)
- [What is a dieline?](https://dielinemaker.com/blog/what-is-a-dieline)
- [Packaging guides](https://dielinemaker.com/blog)
